Switch to the dark mode that's kinder on your eyes at night time.

Switch to the light mode that's kinder on your eyes at day time.

Switch to the dark mode that's kinder on your eyes at night time.

Switch to the light mode that's kinder on your eyes at day time.

in , ,

Reinforcing Steel in Footings

reinforcing-steel-in-footings

Reinforcing Steel in Footings | Those gray bumpy rods are 1/2-inch steel reinforcing bars that will strengthen a garage footing. The contractor now needs to put supports under them so about 3 or 4 inches of concrete separates the rods from the soil. Then it’s time to pour concrete. Copyright 2020 Tim Carter

Reinforcing Steel in Footings – It’s 100X Stronger Than Concrete

QUESTION: Tim, I’m flummoxed. I’m about to build a large detached garage. The plans call for a 10-inch-thick by 20-inch-wide poured concrete footing with two 1/2-inch steel bars that run continuously in the concrete. One bidding contractor says this steel is a waste of time and money while another suggests I upgrade to 5/8-inch steel reinforcing rods. Who’s right? What would you do? What does the steel do? How would you install it if this was your job? I don’t want to make a bad decision here. Sandra P., Ann Arbor, MI

It’s pretty easy to get flummoxed about countless things in residential construction. You can verify this by just reading all of the incoming questions I get on my Ask Tim page at AsktheBuilder.com. Not only do homeowners suffer from confusion, but I also see builders perplexed by all sorts of things. Less than two years ago, an insulation contractor with 20+ years of experienced admitted to me he had been installing insulation wrong his entire career once I pointed out his mistake. CLICK or TAP HERE to read this fascinating story about a contractor that ADMITTED his fault!

What are the benefits of reinforcing steel in footings and concrete?

To understand the benefit of reinforcing steel in concrete, I feel you first need to grasp the physical properties of poured or cast concrete. Back in the mid-1990s, I was invited to an enlightening two-day editors conference hosted by the Portland Cement Association (PCA). From an educational standpoint, it was absolutely the best conference of my entire career.

I was the only member of the media in attendance that had any hands-on construction experience, but even still I discovered much about concrete and reinforcing steel I never knew before.

CLICK or TAP HERE to get FREE BIDS from local footing and foundation contractors.

What does concrete share in common with natural stone?

It’s important to realize that concrete is artificial rock. It’s an extremely complex topic and entire books and careers have been devoted to just the science of concrete. But concrete shares something in common with most natural stone. When mixed and placed correctly, concrete is extremely strong in compression. It can take thousands of pounds of pressure per square inch to shatter or crack concrete.

Is concrete strong in tension?

But concrete only has about one-tenth the amount of strength in tension than it has when you compress or squeeze it. Tension is a bending force. Put a wood toothpick in your hands and snap it in half. That’s tension because you’re bending the wood until it fails. On a microscopic scale, however, one side of the toothpick is in tension as it’s stretching, but the other side is being compressed. This fact is important with respect to the placement of reinforcing steel.

Keep in mind that if you order 4,000 pounds-per-square-inch (PSI) concrete from the plant, that’s its strength in compression. Understand it only takes 400 pounds of force to crack it when you subject the same concrete to a tension, or bending, force.



Will reinforcing steel rods add tensile strength to concrete?

Steel is a magical building material, especially the round reinforcing steel rods you might discover on a construction site. These steel rods are easy to work with and they have incredible tensile strength. The average steel bar you’d find on a construction site might require 40,000 pounds of pulling force before you rip a piece of it in half! You can purchase steel reinforcing rods that even have a rating of 60,000 pounds!

At the PCA editors conference, the scientists demonstrated this. Prior to the conference, they had created some very small concrete beams that measured about 1.5-inches wide, 3/4-inch thick, and about 16-inches long if my memory is correct. One bar had no steel; and in the other one, they had put in two simple long pieces of coat hanger steel like you’d have in your closet. Both concrete bars had been created a month before the conference and had cured under perfect lab conditions. They were as strong as you could get them.

The scientists put the first bar on two pieces of 2×4 to simulate a miniature bridge. This bar had no steel. They then placed in the center of the span, a small 1 pound weight on it slowly and carefully. Within seconds the bar cracked and the bridge collapsed.

Next, they did the same with the bar that had the two coat hanger wires in it. They added one pound, then five more pounds in the center, then I think another five pounds and finally the bar had a significant bend in it, but it had not shattered. This is all you need to know as to why you should always put reinforcing steel in concrete.

Where should the reinforcing steel rods be located in a footer?

The placement of the steel is very important. In a footing, you want the steel in the lower third or so of the concrete. If the footing fails because of poor soil, it’s going to want to stretch along the bottom of the footing while the top is being compressed. Thus, in Sandra’s footing, it would be wise to have about 3.5 inches of concrete under the steel bars.

This same practice should be followed for poured foundation walls. You’d want two rows of steel bars about one foot from the top of the wall and one foot from the bottom. Foundation walls can have tension happen both at the top and the bottom of the wall depending on where the soil below the long walls might fail.

What is the best size of reinforcing bars?

It’s not a bad idea to upsize the steel to 5/8-inch, especially in the footing. The 1/2-inch bars would work just fine in a standard poured foundation wall. But no matter what, always default to what the plans say to do. If you have any questions, always reach out to a residential structural engineer for the answers. CLICK or TAP HERE to get a FREE QUOTE from one. An engineer is always my go-to source.





Column 1379

What do you think?

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Loading…

0
padiglione-agricolo-bressanella-by-a25architetti

PADIGLIONE AGRICOLO BRESSANELLA by a25architetti

water-hammer-fix

Water Hammer Fix

Back to Top
close

Add to Collection

No Collections

Here you'll find all collections you've created before.

Close